Solar Cells and Modules - Revision history

Lisafeldmann at 08:34, 24 June 2026

2026-06-24T08:34:03Z

2026-06-24T07:24:30Z

2019-01-17T11:45:17Z

Monocrystalline Silicon Photovoltaic (PV) Cells

2018-08-01T09:36:41Z

2017-08-02T13:47:48Z

Polycrystalline Silicon Photovoltaic (PV) Cells

2017-08-02T13:37:02Z

2017-08-02T13:35:06Z

2017-08-02T13:25:52Z

Polycrystalline Silicon Photovoltaic (PV) Cells

2015-10-10T14:14:29Z

Further Information

2014-10-13T10:47:57Z

Further Information

@@ Line 113: / Line 113: @@
 <u>In order to use the connected cells in practical applications they must be:</u>
-*protected from mechanical damage during manufacture, transport and [[Solar 365|installation by solar company]] and use (in particular against hail impact, wind, sand and snow loads). This is especially important for wafer-based silicon cells which are brittle.
+*protected from mechanical damage during manufacture, transport and installation by solar company and use (in particular against hail impact, wind, sand and snow loads). This is especially important for wafer-based silicon cells which are brittle.
 *protected from moisture, which corrodes metal contacts and interconnects, (and for thin-film cells the transparent conductive oxide layer) thus decreasing performance and lifetime.

@@ Line 113: / Line 113: @@
 <u>In order to use the connected cells in practical applications they must be:</u>
-*protected from mechanical damage during manufacture, transport and installation and use (in particular against hail impact, wind, sand and snow loads). This is especially important for wafer-based silicon cells which are brittle.
+*protected from mechanical damage during manufacture, transport and [[Solar 365|installation by solar company]] and use (in particular against hail impact, wind, sand and snow loads). This is especially important for wafer-based silicon cells which are brittle.
 *protected from moisture, which corrodes metal contacts and interconnects, (and for thin-film cells the transparent conductive oxide layer) thus decreasing performance and lifetime.

@@ Line 5: / Line 5: @@
 <br/>
 = Monocrystalline Silicon Photovoltaic (PV) Cells<br/> =
-Monocrystalline silicon PV cells are made from silicon wafers that are cut from cylindrical single-crystal silicon ingots. The rotund cells have to be cut to form nearly quadratic cells, that can be easily integrated in one module. Thus, refined silicon is wasted in the cell production process. Monocrystalline silicon shows predictable and uniform behaviour, but, due to the careful and slow manufacturing processes required, it is also the most expensive type of silicon.
+Monocrystalline silicon PV cells are made from silicon wafers that are cut from cylindrical single-crystal silicon ingots. The rotund cells have to be cut to form nearly quadratic cells, that can be easily integrated in one module. Thus, refined silicon is wasted in the cell production process. The cut-off material generated during the squaring process will be usally recycled in the multi-crystalline wafer manufacturing or as incoming material for the polysilsicon producting due to higher cleaning cost for direct feed-in in the CZ-mono crystallization prozess.<br/>
 Modules consisting of monocrystalline silicon PV cells reach commercial efficiencies between 15 and 18&nbsp;%. So far, they are the most efficient modules and, with about 85% in 2010, have the largest market share. However, other alternatives are challenging this technology.

@@ Line 1: / Line 1: @@
+[[Portal:Solar|►Back to Solar Portal]]
 = Overview<br/> =
@@ Line 194: / Line 194: @@
 <references /><br/>
 [[Category:Solar_Home_Systems_(SHS)]]

@@ Line 15: / Line 15: @@
 <br/>
 = Polycrystalline Silicon Photovoltaic (PV) Cells<br/> =
-Polycrystalline or multicrystalline silicon PV cells are made from cast square ingots — large blocks of molten silicon, carefully cooled and solidified. They are less expensive to produce than monocrystalline silicon PV cells, but are marginally less efficient, with module conversion efficiencies between 13 and 16&nbsp;%.
+Polycrystalline or multi crystalline silicon PV cells are made from cast square ingots — large blocks of molten silicon; carefully cooled and solidified. They are less expensive to produce than monocrystalline silicon PV cells, but are marginally less efficient, with module conversion efficiencies between 13 and 16.
-[http://pvcdrom.pveducation.org/ -> PVCDROM.org], an educational website on photovoltaics, shows the production process of polycrystalline silicon PV cells with pictures and viedeo sequences.
+[http://www.pveducation.org/pvcdrom -> PVCDROM.org], an educational website on photovoltaics, shows the production process of polycrystalline silicon PV cells with pictures and video sequences.
 <br/>
@@ Line 27: / Line 28: @@
 <br/>
 = Thin Film Photovoltaic (PV) Cells<br/> =

@@ Line 171: / Line 171: @@
 <br/>
@@ Line 177: / Line 178: @@
 *[[Portal:Solar|Solar Portal on energypedia]]
 *Further information on PV modules in solar home systems see [[Standards for the PV Generator|standards for the PV generator]].
 <br/>